Different Parts of a Toilet Tank You Should Know About

A toilet is such a familiar component of bathrooms that its individual parts are often overlooked. When there is an issue with the toilet, though, it’s vital to know the name of each part, where it is located, and what it does before you can fix the problem. Nearly every part of a toilet can be divided between two main sections, the toilet tank and the toilet bowl, with most of the working parts located in the tank.

Parts of a Toilet: What They Are and How to Fix Them

Lee has over two decades of hands-on experience remodeling, fixing, and improving homes, and has been providing home improvement advice for over 13 years.

Richard Epstein is a licensed master plumber with over 40 years experience in residential and commercial plumbing. He specializes in estimating as well as design and engineering for plumbing systems, and he works for one of New York’s largest union plumbing construction companies.

A toilet is such a familiar component of bathrooms that its individual parts are often overlooked. When there is an issue with the toilet, though, it’s vital to know the name of each part, where it is located, and what it does before you can fix the problem. Nearly every part of a toilet can be divided between two main sections, the toilet tank and the toilet bowl, with most of the working parts located in the tank.

Parts of a Toilet Tank

The toilet tank is the large container above and behind the toilet bowl that holds water to flush away waste in the bowl. Toilet tanks and toilet bowls are usually two separate parts that are attached upon installation. A one-piece toilet is one where the toilet tank and bowl are integrated as a single unit.

Tip

Whenever working on the inside of the toilet tank, first empty the water. Do so by turning off the water supply valve, located near the floor. Then, flush the toilet.

Toilet Handle

The toilet handle is a lever or set of buttons on the front, side, or top of the toilet tank. Pushing the handle sends stored water from the tank rushing into the towel bowl to carry waste down the sewer.

Problems with the toilet handle are often not related to the handle but to mechanisms in the tank like the toilet chain or flapper. When there is a problem with the toilet handle, it’s often because the handle is loose.

To fix a toilet handle, first remove the toilet tank lid. Holding the toilet handle with one hand, use the other hand to rotate the plastic nut inside the tank counter-clockwise (not clockwise) to tighten it.

Toilet Chain and Lift Wire

The toilet chain and attached lift wire respond to pressure from the toilet handle. They lift the toilet flapper to release water into the toilet bowl.

Both parts are located inside the toilet tank, on the other side of the toilet handle. One end of the metal or plastic lift wire is attached to the back of the toilet handle. The other end of the lift wire is attached to the stainless steel toilet chain. The lift wire acts like a crane arm to raise the toilet chain, thus raising the toilet flapper at the bottom of the tank.

The toilet chain links can become snagged or the chain will detach or break. The lift wire may loosen from the toilet handle.

To fix a toilet chain and lift wire, first try unsnagging the chain links if the chain is still attached. Otherwise, remove the lift wire from the handle by turning the plastic nut clockwise (not counter-clockwise). Remove the end of the toilet chain from the flapper, then replace in reverse with the new toilet chain and lift wire.

Toilet Flapper or Flap Valve

The toilet flapper is the hinged flexible rubber valve that opens to permit water from the toilet tank to rush into the toilet bowl. The toilet flapper covers the outlet at the bottom of the tank.

When a toilet makes a hissing sound, one reason is that the toilet flapper has hardened and lost its seal after enough time. Purchase a new 2-inch toilet flapper to replace most flappers.

To replace a toilet flapper, start by emptying the toilet tank of water, then dry the bottom of the tank with a towel. Unhook the flapper from the toilet chain and remove the flapper from the fill tube by unhooking its two ears. Hook the new flapper to the bottom of the fill tube, then attach the toilet chain, then turn the water on again.

Toilet Fill Valve

The toilet fill valve is a vertical plastic tube that helps bring water into the toilet tank, The fill valve also senses when the water level in the tank is at its proper height. The fill tube is located in the toilet tank off-center and directly over the point where the water supply enters the tank.

Toilet fill valves replace the older toilet float or ballcock (a buoyant ball on a lever).

Plastic fill tubes may crack and leak over time. The best solution is to purchase a replacement fill tube and install it in place of the faulty fill tube.

Toilet Float or Ballcock

The toilet float is a round plastic or aluminum ball that is buoyant enough to float on top of the water in the toilet tank. The toilet float is responsible for managing the level of water in the toilet tank.

Toilet floats are generally not found on newer toilets, which use a refill valve instead.

When the toilet float no longer floats on the tank water, the best solution is to install a new float. Symptoms that point to the need for a new toilet float: water flowing after the tank is full; tank not filling completely; or the toilet continually running.

Toilet Overflow Tube

The toilet overflow tube, or flush valve, is a vertical plastic tube in the toilet tank. The overflow tube moves water from the tank to the toilet bowl to prevent water in the tank from overflowing. The overflow tube is also required to fill the bowl to the proper level for the next flush.

Tip

Though it’s easy to confuse the overflow tube with the fill valve, the overflow tube can be identified because it has the flapper valve at the bottom and because it has no sliding floatation device.

To replace a toilet overflow tube, start by turning off the water and emptying the water from the tank. From underneath the toilet tank, remove the bolts and washers. Remove the tank and remove the old overflow or flush valve and gasket. Clean and dry the bottom of the tank, then install the new overflow tube from inside the top of the tank. Install the new gasket on the hole on top of the toilet bowl. Set the tank back in place and bolt it, then turn on the water.

Toilet Water Supply Line and Valve

The water supply (shut-off) valve is an oblong-shaped faucet handle on the pipe that supplies the toilet with fresh water. Water runs through the flexible short braided metal or polymer 3/8-inch from the valve to the toilet.

The supply valve is located at the end of a pipe extending from the wall, a few inches above the floor. The water supply line starts at this valve and ends at the bottom of the toilet tank.

Shut-off valves’ plastic handles are prone to breakage if turned too tightly. Shut-off valves can be removed and inexpensively replaced. The same braided water supply line can be reused if it is still in good condition.

Parts of a Toilet Bowl

Toilet Bowl

The toilet bowl is the large, lower base that removes the waste, plus it’s where the user sits. Most bowls are made of vitreous china, a waterproof material that resists staining well. An internal trap holds fresh water to seal against sewer gasses entering the bathroom.

As a solid piece with no moving parts, the toilet bowl itself rarely malfunctions. Over-tightening the T-bolts at the base or the tank bolts may crack the porcelain. To clear a clogged toilet, use a toilet plunger to force the clog away. If that doesn’t work, use a toilet snake (or auger) to grab onto the clog and extract it.

Tip

Use a bell-shaped toilet plunger with a fold-out flap at the end. An open-end bell-shaped plunger is for sinks, but you can try using it on toilets if a toilet plunger is not available.

Toilet Tank O-Ring Seal

The toilet tank O-ring seal (also called a tank-to-bowl or mack washer) is a round rubber gasket that prevents water from leaking from the bottom of the toilet tank. The O-ring seal is located between the bottom of the toilet tank and the top of the toilet bowl.

When a toilet is leaking between the tank and the top of the bowl, the reason is usually a poorly installed or cracked O-ring seal.

To fix a toilet tank O-ring seal, shut off the water supply and empty the tank. Remove the water supply tube and let its water drain into a container. Underneath the back of the toilet tank and bowl rim, locate the two tank nuts; they may be either metal or plastic. With metal nuts, use a socket wrench underneath to turn out the nuts and remove them. For plastic nuts, turn them out by hand. First remove the tank lid, then lift the tank off of the toilet bowl. Remove the old O-ring seal and clean the area with a soft cloth. Insert the new O-ring seal, cone side pointed down. Reverse the steps to replace the tank.

Toilet Wax or Silicone Seal

The toilet wax seal is a round, cone-shaped collapsible gasket that prevents water from leaking from the bottom of the toilet bowl. The toilet wax seal is located between the bottom of the toilet bowl and the floor flange. Sometimes, this seal is a donut-shaped part made from silicone.

When the toilet is leaking from its base, the wax seal may be dried out, cracked, or too small for the space.

To fix a toilet wax seal, first remove the toilet, then scrape off the old wax ring and dispose of it. Continue to clean off all remnants of the old wax seal thoroughly, then remove the plastic covering from the new wax seal. Press the wax seal on the bottom of the toilet with the plastic cone pointing down. Press the seal hard enough to make it stick but do not compress it. Set the toilet down in a smooth, continuous motion. Make sure that the T-bolts are in place and that they protrude through the holes in the toilet bowl base. Wax seals can only be used once. If you need to reposition a toilet after it has been set down, use a new seal.

Tip

Extra-thick wax rings can help provide a tighter seal when there are height issues. But first try to fix any spacing problems with toilet flange extenders instead of thicker wax rings.

Toilet Floor Flange

The toilet floor flange or closet flange is a round plastic or metal bracket that holds the toilet to the floor with screws and bolts.

The flange is located between the floor and the bottom of the toilet bowl. The flange is attached to the floor with screws, and the toilet is attached to the flange with T-bolts.

Due to movement and the presence of water, floor flanges and their fasteners can rust and break. This may cause the toilet to leak around the bottom.

To fix a toilet floor flange, first turn off the water and empty the tank, then remove the toilet from the floor. Move the toilet away. Unscrew the old flange and scrape off the wax ring and clean thoroughly. Screw the new floor flange directly to the floor. Slide the new T-bolts into the flange with the threads pointing up. Add the washers to hole the T-bolts in place. Replace the toilet.

Tip

If the flange is not flush (even) with the floor surface, install a toilet flange extender.

The two main parts of the toilet are the tank at top and the bowl at bottom. In the toilet tank is the fill tube, the overflow tube, a chain, and a flapper. Older toilets have a floating ballcock. Key parts of the toilet bowl: O-ring seal, wax or silicone seal, and floor flange.

The upper part of a toilet is called the tank. The tank is a reservoir that holds water to flush away waste in the toilet bowl.

The device inside the toilet tank that flushes the toilet is called a toilet flapper or flapper valve. The toilet flapper is raised by depressing the toilet handle.

Different Parts of a Toilet Tank You Should Know About

A toilet is an essential part of any home and is used on a regular basis by you and your family members. Different Parts of a Toilet Tank You Should Know About These problems can lead to things like inefficient flushing, water leaking onto the floor, or even an unpleasant odor lurking around in your bathroom. The toilet tank is an important part of this setup, so understanding how it works and educating yourself about its various parts is a good idea. We take a closer look at these parts and what you should do if you notice problems with your toilet.

Common Parts Of A Toilet Tank

The toilet tank is where water is stored and then pushed into the toilet bowl when you flush. While it may seem like a basic structure from the outside, there are actually several parts that are inside the tank. When your toilet doesn’t flush or keeps leaking water, the issue is usually related to the tank. Let’s discuss the most important parts that form part of the toilet tank.

Tank Cover

One of the first toilet tank parts you will notice is the cover. This is a structure that serves as a lid on top of the toilet tank. While the cover generally does not play a functional role in the tank’s functions, it still forms an important part of the entire toilet. The cover helps to ensure the water that fills the tank won’t splash over the sides, which could leave pools on the floor next to your toilet. The cover also helps to make your bathroom look neater. Some of these covers include a flush button on top, but this is not always the case.

Flush Trigger

Sometimes just referred to as the handle, this particular part is responsible for activating the flushing mechanism when you pull it. Many modern toilets use alternative trigger systems, often with a button instead of a classic trigger. Regardless, the purpose of this trigger is important – without it, you will not be able to create a reaction inside the bowl that causes water to flush down toward the toilet bowl.

Flush Valve

As water fills the toilet tank, it needs to remain in this reservoir until you need to flush it into the bowl. This is where the flush valve comes into the picture. This particular valve sits at the bottom of the toilet tank. There are different types of flush valves that manufacturers use, so it’s not always the same. In most cases, these valves use either plastic or metal materials in their construction. The flush valve also generally consists of the opening itself that allows water to transfer from the tank to the bowl. Some examples of valve options include:

• Canister valves
• Flapper valves
• Ballcock valves
• Diaphragm valves

Toilet Tank Flapper

The next part that we are going to talk about is the toilet tank flapper. This particular part of the toilet sits on top of the flush valve and regulates the movement of water from the tank through the valve. The flapper is connected to an internal system inside the toilet tank, which is triggered by the handle you use when you want to flush the toilet. When you pull or push on this lever, then a chain pulls the flapper upward. This creates an opportunity for the water to flush down the valve. Once the lever goes back up, the flapper moves down into the valve in order to seal it again.

Flapper Lift Chain

There is a chain attached to the flapper, which has a connection to the flush lever. This particular chain creates tension when you push down the toilet lever. The chain needs an adjustment to ensure it does not push the flapper too much back after flushing, as this can cause leakage from the tank into the bowl. At the same time, the chain should still produce enough tension to lift the flap up properly.

Toilet Fill Valve

After you flush your toilet, water needs to start flowing into the tank again. This ensures there will be sufficient water for the next flush. The filling of the tank is regulated by the toilet fill valve. This is a lengthy piece that connects directly to the water supply. There are parts that connect to the toilet fill valve, which consists of the refill tube and the toilet float. Together, these three regulate the flow of water from the supply into the tank.

Float Ball

If you open up the toilet tank, you’ll see a floating ball that looks almost like a balloon on the water. It connects to the fill valve and helps to ensure the process of filling the toilet stops when there is enough water inside. The ball will float at the top of the tank. When you flush the toilet, it goes down with the water. As water enters the tank again, the float ball will also rise upward. When it is at the correct position, it stops the fill valve from pushing more water into the tank.

Refill Tube

You’ll always see some water at the bottom of your toilet, even after flushing. This water comes from the refill tube. It is a technique used to prevent sewer gases from entering your home. After your toilet flushes, some water is sent into the bowl with a delay. This is the water you see at the bottom of the toilet and is held by the refill tube during the flushing process. By ensuring sewer gases do not enter during a flush, you can effectively avoid having unpleasant smells in the bathroom.

Conclusion

The tank of your toilet holds water and allows you to flush debris after you use the toilet. There are numerous components that play important roles in the tank. Damage or a malfunction in any part can lead to problems with your toilet. Understanding the role of these parts can help you assess a situation and identify the fault. For professional toilet repair services in Metro Detroit, contact Waterwork Plumbing – we are the pros in the area and have significant experience in the plumbing industry.